DIP Switch Settings and Pin Definitions¶
Power Board Connector – PWR1¶
Pin |
Signal |
|---|---|
1 |
DC_GND |
2 |
DC_IN |
3 |
ALARM2 |
4 |
ALARM1 |
5 |
DC_IN |
6 |
DC_GND |
Voltage Range: +12 ~ +36V
Internal Jumpers & Connectors¶
JCMOS1 – RTC Reset Jumper¶
Jumper |
Function |
|---|---|
1–2 |
Clear CMOS for RTC |
2–3 |
Clear CMOS for SRTC |
Pin |
Signal |
|---|---|
1 |
RTC_RST# |
2 |
NC |
3 |
SRTC_RST# |
J8 – Power SMBus Debug Header¶
Pin |
Signal |
|---|---|
1 |
GND |
2 |
SMB_CLK_VR |
3 |
SMB_DATA_VR |
J18 – MCU Programming Header (Debug/Burn-In)¶
Jumper |
Function |
|---|---|
1–2 |
Disable (Default) |
2–3 |
Enable |
Pin |
Signal |
|---|---|
1 |
+P3V3_STBY |
2 |
PIO1_1_GPIO2 |
3 |
GND |
J17 – LTE Module GPS Selection¶
Jumper |
Module Selected |
|---|---|
1–2 |
EM7455 / MV31-W / RM00Q |
2–3 |
FN980 |
Pin |
Signal |
|---|---|
1 |
+P3V3 |
2 |
W_DIS2#_OE |
3 |
GND |
COM1 – Serial Port¶
Pin |
Signal |
|---|---|
1 |
N/A |
2 |
RX |
3 |
TX |
4 |
N/A |
5 |
GND |
6 |
N/A |
7 |
RTS |
8 |
CTS |
9 |
N/A |
JDebug1 – UART Debug Header¶
Pin |
Signal |
|---|---|
1 |
+P3V3_STBY |
2 |
GND |
3 |
UART_TX |
4 |
UART_RX |
JSPI1 – SPI Debug Header¶
Pin |
Signal |
|---|---|
1 |
SPI0_IO3_HOLD# |
2 |
NC |
3 |
SPI0_CS0_R# |
4 |
+P3V3_STBY_SPI |
5 |
SPI0_IO1_MISO_R |
6 |
NC |
7 |
NC |
8 |
SPI0_CLK_R |
9 |
GND |
10 |
SOC_SPI_MOSI_R |
JPW1 – Power Supply Header¶
Pin |
Signal |
|---|---|
1 |
+P12V |
2 |
GND |
3 |
GND |
4 |
+P5V |
ESPI1 – Embedded SPI Interface¶
Pin |
Signal |
Pin |
Signal |
|---|---|---|---|
1 |
ESPI_CLK |
2 |
ESPI_IO1 |
3 |
ESPI_RST# |
4 |
ESPI_IO0 |
5 |
ESPI_CS0# |
6 |
+P3V3 |
7 |
ESPI_IO3 |
8 |
NA |
9 |
ESPI_IO2 |
10 |
GND |
11 |
+P3V3_STBY |
12 |
NC |
DP1 – Debug Port¶
Note: This port is for debug use only and cannot be used simultaneously with the IPMI interface.
Carrier Board Connector¶
JDebug1 – UART Debug Header (Carrier Board)¶
Pin |
Signal |
|---|---|
1 |
+P3V3_STBY |
2 |
GND |
3 |
UART_TX |
4 |
UART_RX |